Water Management

Jacuzzi PROCLEAR Water Management System Start Up Procedure

1. Attach Prefilter to hose and begin filling spa in the spa filter area.

2. While spa is filling, add 4 ounces of Metal Magnet.

3. After spa is filled to proper level, (approximately halfway up filter intake grid), turn on spa and wait until spa reaches desired temperature.

4. Test spa water with test strips.  Adjust Ph if necessary to between 7.2 and 7.6.  If Ph is high, add Power Down.  If Ph is low add Power Up.  Always run jets when adding chemicals to the spa.  Allow jets to run at least 20 minutes.  Retest.  Repeat this procedure until proper Ph level is achieved.

5. Add 4 ounces of  Water Polish.  Allow to circulate 1-4 hours.

6. Turn spa off.  Remove and rinse out spa filters. 

7. Remove the circulation pump filter cap.  (The circulation pump filter is the one that when removed has a permanent screen beneath it over the intake hole.)  Install the Jacuzzi ProClear Mineral Spa Sanitizer in the filter cap recess.  Replace the cap.  Install both filters in Spa.

8. Add 2-3 tablespoons of Boost.  Allow to circulate 20-30 minutes.  Spa is now ready to use.


Jacuzzi PROCLEAR Water Maintenance

1. Be sure to replace the ProClear Mineral Sanitizer every 3 months.

2. During the first 10 days, on any day the spa is used, after the last use of the day, you must add Boost.  Under light use, (1-2 people for 30-60 minutes), 1-2 tablespoons.  Under moderate use, (3-4 people for 60-90 minutes), 3-4 tablespoons.  Under heavy use, (4+ people for 60+ minutes) 4-6 tablespoons or more may be required.  If the spa is not used during the the first 10 days you should add 1-2 tablespoons of Boost every 4-5 days.

3. After the first 10 days, on any day the spa is used, after the last use of the day, you must add either Oxyburn or Boost.  Under light use, (1-2 people for 30-60 minutes), 3-6 tablespoons or more of Oxyburn is effective at maintaining water clarity when using the Jacuzzi ProClear Mineral Spa Sanitizer every 3 months.  This allows for spa use with little Chlorine in the water at the time of use.  If using Oxyburn on a regular basis, substitute Boost for the Oxyburn at least once a week to prevent growth of any resistant bacteria to the Jacuzzi ProClear Mineral Spa Sanitizer.   Under moderate to heavy use, it is recommended to use Boost instead of Oxyburn to maintain proper water chemistry. Under moderate use, (3-4 people for 60-90 minutes), 3-4 tablespoons of Boost.  Under heavy use, (4+ people for 60+ minutes) 4-6 tablespoons or more of Boost may be required.

4. Test water at least once a week to check Ph and maintain the Ph in the 7.2 – 7.6 range using the procedures described above.

5. If spa is getting light to moderate use, turn off spa and remove and rinse out filters at least once a month.  Under heavy use, rinse filters every 2 weeks. Soak filters in Filter Cleanse solution every 3 months. Replace filters every 12 months.


Jacuzzi PROCLEAR Water Maintenance Tips and Recommendations

1. Drain and refill spa every 3-6 months depending on use.  Never attempt to drain spa when temperature is below freezing.

2. Use Spa Perfect once a week to help prevent scum lines and improve filter performance.

3. If experiencing spa foaming, use a very small amount of Foam Away with jets running. Foam will dissipate in a couple minutes.  Using too much Foam Away can cause a gummy scum line at the water line.

4. If experiencing consistent, excessive spa foaming, this is usually a sign of improper water chemistry, typically lack of using enough Boost, improper Ph, or both.  To correct without draining spa, test and adjust Ph to proper range if needed.  Then add 1/2  to 1 cup of  Boost.  The next day add 3-4 ounces of Water Polish.  The next day, rinse out the filters.

5.  When using the Jacuzzi ProClear Mineral Spa Sanitizer, any day you go out to use the spa and the water is not clear, prior to entering the spa, you must add Boost in a sufficient amount to obtain a 5ppm Chlorine level when tested.  Allow Boost to circulate at least 30 minutes prior to entering spa.


ECO-PURE Water Management System

1.  Always fill spa using the FIRST STEP CLEAN ‘N FIL (part# JD-SPF).

2.  Add 4oz. of METAL MAGNET (part# 95001).

3.  Allow to circulate while spa is heating (5 hours minimum).

4.  When spa is hot (100 degrees), test water with TEST STRIPS (part# ETS-511244).

5.  Balance the pH level using teaspoons of POWER DOWN (part# 32001)  if level is high or POWER UP (part# 36001) if the pH level is low.

6.  Add 4 oz. of WATER POLISH (part# 96001). Allow to circulate for five hours.

7.  Repeat step 5, then hose out filters, go to step 8.

8.  Add 1oz. of BOOST and allow to circulate for 20 minutes.  At this point you are ready to use the spa.  NOTE:  the ECO-PURE cartridge, inside the filter, can take up to 2 weeks to establish the proper ion level.  As you are using the spa, the ion level can be used up.  Therefore, it is very important that you use chlorine after each use for the first 10 days to 2 weeks.  This will allow the ion level to be established.  Once this has occurred, proceed to the next step.

9.  Routine:  Check pH level twice weekly.  Add 1 to 2 oz. OXY BURN after each use.  You can’t add too much OXY BURN.  If the use is heavy or extended, add 1 oz. of BOOST.  If the heavy or extended use is daily, use BOOST more frequently.

10.  Hose out filters every two weeks.  Soak in FILTER CLEANSE (part# 87001) once a month.  Do not soak the ECO-PURE cartridge.  The ECO-PURE cartridge needs replaced every six months.  The main filters are the lifeblood of your spa.   Replace main filters every year.


SilSpa Water Management System

1.  Always fill spa using the FIRST STEP CLEAN ‘N FIL (part# JD-SPF).

2.  Add 4 oz. of METAL MAGNET (part# 95001).

3.  Allow to circulate while spa is heating.  (Five hours minimum)

4.  When spa is hot (100 degrees), test water with TEST STRIPS (part# ETS-511244).

5.  Balance the pH level using teaspoons of POWER DOWN (part# 32001)  if level is high or POWER UP (part# 36001) if the pH level is low.

6.  Add 4 oz. of WATER POLISH (part# 96001). Allow to circulate for five hours.

7.  Repeat step 5, then hose out filters, go to step 8.

8.  Shake SilSpa bottle vigorously and thoroughly.  Then, shake it some more!  (Be sure that each time you add SilSpa that you vigorously and thoroughly shake the bottle!).

9.  Add 6 oz. of SilSpa (part# 40006) directly in front of jets.  Allow to circulate for 15 minutes.

10.  Add 2 oz. of OXY BURN and allow to circulate for 15 minutes.  YOU ARE READY TO USE THE SPA!

11.  Routine:  Add 6 oz. of SilSpa once a month, every month.  Add 2-3 ounces of OXY BURN each day that the spa is used.  If the spa is used daily, you may use OXY BURN daily.  You should use 2-3 oz. of BOOST (part# 13001) in place of OXY BURN after heavy or extended use.  Check and maintain proper pH level.

12.  Hose out filters every two weeks.  Soak in FILTER CLEANSE (part# 87001) once a month.  The filters are the lifeblood of your spa.